First commit

GateWay/src/main.cpp

@@ -0,0 +1,141 @@
+#include <Arduino.h>
+
+/* * LED purposes:
+ * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
+ * - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received
+ * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
+ * - ERR (red) - fast blink on error during transmission error or receive crc error
+ *
+ */
+
+#define MY_DEBUG
+#define MY_BAUD_RATE 9600
+#define MY_RADIO_RF24
+#define MY_GATEWAY_ESP8266
+// #define MY_DISABLED_SERIAL
+// #define MY_SPLASH_SCREEN_DISABLED
+#define MY_RF24_PA_LEVEL (RF24_PA_MAX)
+#define MY_RF24_CHANNEL (15)
+#define MY_RF24_DATARATE (RF24_250KBPS)
+
+#define MY_WIFI_SSID "wf-home"
+#define MY_WIFI_PASSWORD "0ndthnrf"
+
+#define MY_HOSTNAME "ESP8266_GW"
+
+#define MY_PORT 5003
+
+// How many clients should be able to connect to this gateway (default 1)
+#define MY_GATEWAY_MAX_CLIENTS 12
+
+// #define MY_DEFAULT_LED_BLINK_PERIOD 300
+
+// Flash leds on rx/tx/err
+#define MY_DEFAULT_ERR_LED_PIN D3  // Error led pin
+#define MY_DEFAULT_RX_LED_PIN  D4  // Receive led pin
+//#define MY_DEFAULT_TX_LED_PIN  1  // the PCB, on board LED
+#define MY_WITH_LEDS_BLINKING_INVERSE
+#define MY_RF24_CE_PIN D0
+
+#include <ArduinoOTA.h>
+#include <MySensors.h>
+#include "SdsDustSensor.h"
+
+int rxPin = D1;
+int txPin = D2;
+SdsDustSensor sds(rxPin, txPin);
+
+unsigned long cRun;
+int cSec = 0;
+
+#define CHILD_ID_25 0
+#define CHILD_ID_10 1
+
+MyMessage msg25(CHILD_ID_25, V_VAR1);
+MyMessage msg10(CHILD_ID_10, V_VAR2);
+
+void setup()
+{
+  WiFi.begin(MY_WIFI_SSID, MY_WIFI_PASSWORD);
+  if(WiFi.waitForConnectResult() == WL_CONNECTED){
+    delay(500);
+    Serial.print(".");
+  }
+  Serial.println("");
+  Serial.print("Connected to ");
+  Serial.println(MY_WIFI_SSID);
+  Serial.print("IP address: ");
+  Serial.println(WiFi.localIP());
+
+	ArduinoOTA.onStart([]() {
+		Serial.println("ArduinoOTA start");
+	});
+	ArduinoOTA.onEnd([]() {
+		Serial.println("\nArduinoOTA end");
+	});
+	ArduinoOTA.onProgress([](unsigned int progress, unsigned int total) {
+		Serial.printf("OTA Progress: %u%%\r", (progress / (total / 100)));
+	});
+	ArduinoOTA.onError([](ota_error_t error) {
+		Serial.printf("Error[%u]: ", error);
+		if (error == OTA_AUTH_ERROR) {
+			Serial.println("Auth Failed");
+		} else if (error == OTA_BEGIN_ERROR) {
+			Serial.println("Begin Failed");
+		} else if (error == OTA_CONNECT_ERROR) {
+			Serial.println("Connect Failed");
+		} else if (error == OTA_RECEIVE_ERROR) {
+			Serial.println("Receive Failed");
+		} else if (error == OTA_END_ERROR) {
+			Serial.println("End Failed");
+		}
+	});
+	ArduinoOTA.begin();
+  sds.begin();
+
+  // Serial.println(sds.queryFirmwareVersion().toString()); // prints firmware version
+  // Serial.println(sds.setActiveReportingMode().toString()); // ensures sensor is in 'active' reporting mode
+  // Serial.println(sds.setCustomWorkingPeriod(3).toString()); // sensor sends data every 3 minutes
+  sds.setActiveReportingMode();
+  sds.setCustomWorkingPeriod(1);
+
+  cRun = millis();
+}
+
+void presentation()
+{
+	sendSketchInfo("GateWayDust", "2.0");
+	present(CHILD_ID_25, S_AIR_QUALITY, "Dust 2.5");
+  wait(50);
+	present(CHILD_ID_10, S_AIR_QUALITY, "Dust 10");
+}
+
+void loop()
+{
+	// Send locally attached sensors data here
+	ArduinoOTA.handle();
+  if(cRun + 1000 < millis()){
+    cRun = millis();
+    PmResult pm = sds.readPm();
+    cSec++;
+    if (pm.isOk()) {
+      // Serial.print(cSec); Serial.print("\t");
+      // Serial.print("PM2.5 = ");
+      // Serial.print(pm.pm25);
+      // Serial.print(", PM10 = ");
+      // Serial.println(pm.pm10);
+
+      // // if you want to just print the measured values, you can use toString() method as well
+      // Serial.println(pm.toString());
+      send(msg25.set(pm.pm25, 1));
+      wait(100);
+      send(msg10.set(pm.pm10, 1));
+      cSec = 0;
+    //} else {
+      // // notice that loop delay is set to 5s (sensor sends data every 3 minutes) and some reads are not available
+      // Serial.print(cSec); Serial.print("\t");
+      // Serial.print("Could not read values from sensor, reason: ");
+      // Serial.println(pm.statusToString());
+    }
+  }
+}