Added mysensors gateway & midroom light

SerialGateWayMyS/src/main.cpp

@@ -0,0 +1,102 @@
+#include <Arduino.h>
+/**
+* The MySensors Arduino library handles the wireless radio link and protocol
+* between your home built sensors/actuators and HA controller of choice.
+* The sensors forms a self healing radio network with optional repeaters. Each
+* repeater and gateway builds a routing tables in EEPROM which keeps track of the
+* network topology allowing messages to be routed to nodes.
+*
+* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
+* Copyright (C) 2013-2019 Sensnology AB
+* Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
+*
+* Documentation: http://www.mysensors.org
+* Support Forum: http://forum.mysensors.org
+*
+* This program is free software; you can redistribute it and/or
+* modify it under the terms of the GNU General Public License
+* version 2 as published by the Free Software Foundation.
+*
+*******************************
+*
+* DESCRIPTION
+* The ArduinoGateway prints data received from sensors on the serial link.
+* The gateway accepts input on serial which will be sent out on radio network.
+*
+* The GW code is designed for Arduino Nano 328p / 16MHz
+*
+* Wire connections (OPTIONAL):
+* - Inclusion button should be connected between digital pin 3 and GND
+* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
+*
+* LEDs (OPTIONAL):
+* - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs
+* - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received
+* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
+* - ERR (red) - fast blink on error during transmission error or receive crc error
+*
+*/
+
+// Enable debug prints to serial monitor
+#define MY_DEBUG
+
+
+// Enable and select radio type attached
+#define MY_RADIO_RF24
+//#define MY_RADIO_NRF5_ESB
+//#define MY_RADIO_RFM69
+//#define MY_RADIO_RFM95
+
+// Set LOW transmit power level as default, if you have an amplified NRF-module and
+// power your radio separately with a good regulator you can turn up PA level.
+#define MY_RF24_PA_LEVEL RF24_PA_HIGH
+
+// Enable serial gateway
+#define MY_GATEWAY_SERIAL
+
+// Define a lower baud rate for Arduinos running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
+#if F_CPU == 8000000L
+#define MY_BAUD_RATE 38400
+#endif
+
+// Enable inclusion mode
+//#define MY_INCLUSION_MODE_FEATURE
+// Enable Inclusion mode button on gateway
+//#define MY_INCLUSION_BUTTON_FEATURE
+
+// Inverses behavior of inclusion button (if using external pullup)
+//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
+
+// Set inclusion mode duration (in seconds)
+//#define MY_INCLUSION_MODE_DURATION 60
+// Digital pin used for inclusion mode button
+//#define MY_INCLUSION_MODE_BUTTON_PIN  3
+
+// Set blinking period
+#define MY_DEFAULT_LED_BLINK_PERIOD 300
+
+// Inverses the behavior of leds
+#define MY_WITH_LEDS_BLINKING_INVERSE
+
+// Flash leds on rx/tx/err
+// Uncomment to override default HW configurations
+#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
+#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
+#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED
+
+#include <MySensors.h>
+
+void setup()
+{
+	// Setup locally attached sensors
+}
+
+void presentation()
+{
+	// Present locally attached sensors
+}
+
+void loop()
+{
+	// Send locally attached sensor data here
+}